DIAMOND STEEL^TM is a blend of sized inert carbon particles. Each particle is held together by a system of covalent, carbon-carbon bonds. Essentially, each particle is a system of large arrays of aromatic rings, fused together at carbon apices, with only a limited number of heteroatoms located primarily at crystal edge sites. Although these particles can form a thin film by the cleavage of adjacent carbon "sheets," breakage across a sheet requires very high energy. As a result, these particles have no known solvent under normal conditions.

There are no organic oils, ketones, ethers, etc., which are known to attack them. Therefore, DIAMOND STEEL^TM (Fine) is an excellent additive for synthetic oil fluids. The particles do not swell, or react with clay formations. Accordingly, back flushing of oil and/or gas from producing reservoirs appears to remove the particles and reservoir impairment does not appear to be a problem. However, the particles do have a certain amount of flex which helps to prevent reduction in particle size distribution during drilling operations.

Through our research and development we have found the key to the success of a loss circulation material is the particle size distribution. The absence of a proper distribution will result in failure in severe conditions. The differences in particle size cannot be seen with the naked eye. It is determined by careful screening and then blended according to percentages determined by exhaustive testing DIAMOND STEEL^TM is a superior loss circulation material when compared to like additives due to its composition and particle size distribution.

Primary Applications

DIAMOND STEEL^TM can be added to the active mud system and allowed to circulate while drilling, but the ideal application is to add from 10 to 20 pounds per barrel in sweeps.
It performs in oil or water base drilling fluids.
Laboratory tests with synthetic oil fluid using a 190-micron disk reveal almost total sealing while testing at 2500 psi and 250 degrees F. This is a very severe test and very few products are able to seal with any efficiency. The base mud fails immediately with no control.

Physical Properties

Appearance: Black granule with silver luster
Specific gravity: 2.22-2.25
Dispersible (not soluble): Water & Oil

Packaging/Handling

DIAMOND STEEL^TM is completely environmental safe. It can be land farmed, dumped overboard or spilled with no harmful effects.
It is packaged in multi walled paper bags at 50 pounds each.
Please read the MSDS before handling this product.
DIAMOND STEEL^TM has definite advantages over conventional fiber applications when trying to seal fractures. Particle size distribution and amount of bridging agent are the two most important factors. By its make up, higher concentration of DIAMOND STEEL^TM can be used with much less effect on mud properties.

“DIAMOND SQUEEZE"^TM is a whitish product with various LCM products which when squeezed will turn into a hard mud cake. The product is to be mixed and pumped across the appropriate interval and squeezed into the zone. In this liquid state the DIAMOND SQUEEZE^TM will migrate into the formation naturally. By applying pressure on the pill it will squeeze further into the formation and turn into a semi solid state. While holding pressure after a designated period of time it will turn into a solid state.

DIAMOND SQUEEZE^TM can be designed to be acid soluble and is completely environmentally safe. This allows DIAMOND SQUEEZE^TM to be used while drilling as an LCM and in multiple production zones as a completing aid where each zone can be completed independently without fear of formation damage.

Primary Applications

Acid soluble.
Seals extreme lost circulation problems.
Seals large fractures.
Seals highly depleted sands.
Seals weak channeling and underground crossflows.

Physical Properties

Appearance: Whitish Powder
Bulk Density: 35#/cu. ft.

Packaging/Handling

DIAMOND SQUEEZE^TM is packaged in 40 pound multi walled paper bags.
Each pallet contains 50 bags.
Each pallet is shrink wrapped for product protection.

---

DIAMOND CARB FINE^TM
DIAMOND CARB MEDIUM^TM

“DIAMOND CARB”^TM (FINE & MEDIUM), are premium, calcium carbonate and bagged separately according to particle sizes. System treatment levels range from 4 to 10 ppb, while pill concentrations vary from 10 to 50 ppb.

DIAMOND CARB^TM (FINE & MEDIUM), can be used in conjunction with any other LCM in pill form.

Primary Applications

Seals depleted sands.
Prevents sticking and seepage losses.
Is acid soluble.

Physical Properties

Appearance: White powder.
Bulk Density: 50# per 1500 cu. in.

Packaging/Handling

DIAMOND CARB^TM (FINE & MEDIUM), is provided in 50 pound bags, 50 bags per pallet. Each pallet is shrink wrapped for protection.

---

DIAMOND MULTI-CARB^TM

DIAMOND MULTI-CARB^TM is a special blend of various particle sizes of calcium carbonate with a proprietary additive. This product can be used in water-base and oil-base muds, as well as work over fluids as a source of acid soluble LCM.

DIAMOND MULTI-CARB^TM enhances a fluid’s particle size distribution (PSD), seals depleted sands, and inhibits hydration of sensitive shales.System treatment levels range from 4 to 10 ppb, while pill concentrations vary from 10 to 50 ppb.

DIAMOND MULTI-CARB^TM can be used in conjunction with any other LCM in pill form.

Primary Applications

Seals depleted sands.
Prevents sticking and seepage losses.
Is acid soluble.

Physical Properties

Appearance: White powder.
Bulk Density:50# per 1500 cu. in.

Packaging/Handling

DIAMOND MULTI-CARB^TM (FINE & MEDIUM), is provided in 50 pound bags, 50 bags per pallet. Each pallet is shrink wrapped for protection.

---

DIAMOND SWEEP^TM

Product Description Will Be Available Shortly.

---

DIAMOND RIG DEGREASER^TM
Degreaser/Precision Cleaner

DIAMOND RIG DEGREASER^TM is a high performance degreaser/cleaner designed to clean the toughest of oil-based mud’s, oily cuttings, grease-soiled equipment, slippery decks/railing, etc. The product was formulated to pass stringent airline, aircraft manufacturer, and government specifications, while providing the cleaning coefficient of solvents no longer admissible or used.

As a precision cleaner, DIAMOND RIG DEGREASER^TM can be used in heated tanks, automatic washers, or by ambient temperature soaking, for water break-free rinsing.

Primary Applications

D.O.T. Non-Regulated and meets or exceeds all environmental standards involving degreaser/cleaners.
A broad-spectrum cleaner capable of replacing numerous products in a drilling operation; cuttings wash, thread cleaner, degreaser, bilge cleaner, deck cleaner, living quarters mopping solution, and equipment sump clean out product.
Water-soluble and can be diluted from 1:1 to 1:64 for a myriad of soiled surfaces.

DIAMOND RIG DEGREASER^TM can be applied neat, but is normally diluted with fresh water at a ratio of 1:1 up to 1:10 depending on the amount of grease present. Apply product and allow soaking the surface for chemical contact time, removing solvated soils by pressure washing, brushing, or mopping until thoroughly clean.

Physical Properties

Appearance/Physical State:	Blue Liquid/Mild Lemon Odor.
Density:	8.5 lbs./gal.
Flash Point:	155° F.
pH (5% in IPA/Water):	12.7.
Pour Point:	(-) 5° F.
Solubility, 10% in the following:
Water: Soluble Seawater Soluble Diesel Dispersible

Packaging/Handling

DIAMOND RIG DEGREASER^TM is packaged in 5 Gallon Plastic Pails, 55 Gallon Drums, and USCG/DOT Approved Totes.

---

TRIPACK^TM CI
(Packer Fluid Inhibitor)

TRIPACK^TM CI is a combination chemistry consisting of a filming amine, cationic surfactant, oxygen scavenger, and scale inhibitors. This unique packer fluid inhibitor was designed to treat corrosion due to entrained corrosive gases, microbe contamination, and by applying a film to all metal surfaces contacted. The product contains scale inhibitor compounds that will prevent scale and associated under-deposit corrosion problems in the annular space.

TRIPACK^TM CI will lengthen casing and tubing life by years of effective service. The product was designed to pass all major oil company in-house lab tests and perform in the field.

Primary Applications

Effective in all water, brines, or clear fluid systems.
Passes all major oil company efficacy and environmental tests, both by in-house and outside lab services.
Prevents and removes microbial cell site formation; the product will eliminate underdeposit corrosion due to sessile layers of biofilm.
Effective at concentrations as low as 1:100 (1.0% by volume). One fifty-five gallon drum will treat between 100 to 125 barrels of packer fluid.

Physical Properties

Appearance/Physical State:	Light Amber Liquid/Mild Odor.
Density:	8.6 lbs./gal.
Flash Point:	107° F.
pH (5% in IPA/Water):	8.7.
Pour Point:	5° F.
Solubility, 10% in the following:
Water: Soluble 9 lb. Brine Soluble 11 lb. Clear Fluid Brine Soluble Diesel Insoluble Methanol Soluble

Charge system with one fifty five gallon drum of TriPack CI in each 100 barrels of packer fluid for optimum treatment effectiveness.

Packaging/Handling

TRIPACK^TM CI is packaged in 5 Gallon Plastic Pails, 55 Gallon Drums, and USCG/DOT Approved Totes.

---

S.O. LUBE 1000^TM
(R.O.P. ENHANCEMENT)

S.O. LUBE 1000^TM is a 100% petroleum based, extreme pressure, biodegradable, pollution free drilling lubricant designed to be a one-step lubricant for use in all troublesome wells.

S.O. LUBE 1000^TM is formulated to provide the following benefits:

Increases R.O.P. with 3% - 6% concentration

Minimizes torque and drag

Minimizes Differential sticking

Stabilizes the well bore and therefore preventing sloughing shales by lowing the high temperature, high pressure water loss and forming a durable filter cake

Eliminates bit balling and thereby improves the penetration rate by allowing more weight on the bit and increased rotary table RPM

Reduces wear on all down hole tools and casing in directional wells to reduce the likelihood of a twist off and/or fishing job

Assists in reducing drag when logging tools are being run

Compatibility with all types of mud systems

It helps prevent washout when drilling through a salt zone because S.O. LUBE 1000^TM will not dissolve salt

Minimizes premature bit bearing failure, thereby helping to reduce the number of bit changes

Does not affect the Theological properties of any mud system

Will not be affected by temperatures up to 500O degrees F

Can be checked on a retort. Will show as oil and will separate from diesel oil on retort. Example: If there is 3% diesel in a system and 2% S.O. Lube 1000, a 5% oil content will show in the mud. S.O. LUBE 1000^TM will be on top of the diesel and a shade darker color

S.O. LUBE 1000^TM passes the Static Sheen Test preformed on the rigs

S.O. LUBE 1000^TM has proven many times in different mud systems to increase rate of penetration when 3% - 6% is added to mud system, no matter the type of bit that is in the hole.

A few of the mud systems that have been successful are:

Fresh water lignosulfonates up to 17.3#/BBL. Callon Petroleum, State lease 15543 #1, Mallard Rig #57, Venice, LA. Up to 44 feet per hour with motor bit.

Baker Inteq's Aqua-Drill Plus - Stone Energy Corp., OCSG 1238 #2, Block 23, South Pelto Field, Noble Drilling Co. Rig "Max Smith". Running a 9.875 PDC bit from Diamond Products Inc. From 4 feet per hour to 15 feet per hour.

Seawater lignosulfonate, M.I. Drilling Fluids - Marathon Oil Co., OCSG 14621, Block 829 #1, STI Ewing Banks, Diamond "M" Drilling Co. "Ocean Lexington" Rig. Running a 12.250 bi-center #SR244 PDC bit. From 8.8 feet per hour to 12.10 feet per hour.

Baroid's Glycol Enhanced Muds (GEM) Santa Clara Field, CA, Platform Gilda, S-28 RD, Torch Energy.

Fresh water Lig/CLS, SBM Drilling Fluids - Aviara Energy Corp., R.L Smith #2 R/E, Greywolf Rig #83, North Ridge Field. From 8-12 feet per hour to 30-50 feet per hour.